SLS Nylon Glassfilled(PA12+GF)
The surface of the material is white and slightly granular and porous. Nylon Glassfilled(PA3200 GF) is more durable and resistant than Nylon (PA12). It gives you great freedom in your designs - allowing for both complex and inclosed volumes. The material is great for technical parts that need resistance and loads. The surface is not as accurate as polyamide 12 but it will fit the requirements of technical parts.
3 x 3 x 3 mm
Default Layer Height:
Optional Layer Heights(mm):
±0.3% (with a lower limit of ±0.3 mm)Heat endurance:
Available Post Process
Suitable ForFunctional prototypes and end products,
Complex designs with intricate details,
Moving and assembled parts,
Cases, holders, adapters,
Form and fit testing,
Functional prototyping and testing
Not Suitable For
Fine-detail models with smooth surfaces,
Nylon 3200 Glass-filled (glass-filled nylon) is a great 3D printing material that allows complex and resistant models. It is durable and strong that's why it perfectly fits technical uses. Nylon 3200 Glass-filled (glass-filled nylon) is used in many industries such as the automotive industry. It can be placed near engines and used for parts that require a lot of stresses and loads.
Complex models can be realized in glass-filled nylon, just as enclosed volumes. However, t he surface of the glass-filled polyamide 3D printed objects is limited to 100 µm that means fine details will not be optimally printed. Nylon 3200 Glass-filled (glass-filled nylon) is indeed an engineering material that is used for technical parts that require particular stiffness, high heat distortion temperature and low abrasive wear.
The surface quality of the Nylon 3200 Glass-filled (glass-filled nylon) is excellent and designed for uses in dirty environments.
It is mainly used for parts with requirements on abrasion and wear, stiff housings, parts used under elevated thermal conditions (for example for final parts within the engine area of cars), for deep-drawing dies, or for any other application which requires particular high heat distortion temperature, low abrasive wear and special stiffness.
| Min Supported Wall Thickness|
A supported wall is one connected to other walls on two or more sides.
| Min Unsupported Wall Thickness|
An unsupported wall is one connected to other walls on less than two sides.
| Min Supported Wires|
A wire is a feature whose length is greater than five times its width. A supported wire is connected to walls on both sides.
| Min Unsupported Wires|
A wire is a feature whose length is greater than five times its width. An unsupported wire is connected to walls on less than two sides.
| Min Embossed Detail|
A detail is a feature whose length is less than twice its width.
The minimum detail is determined by the printer's resolution.When detail dimensions are below the minimum, the printer may not be able to accurately replicate them. Details that are too small can also be smoothed over in the polishing process.
To ensure details come out clearly, make them larger than the indicated minimum. We may refrain from printing products with details smaller than the minimum, since the final product will not be true to your design. If your product has details smaller than the minimum, try making them larger, removing them, or considering a material with finer detail.
| Min Engraved Detail|
A detail is a feature whose length is less than twice its width. Engraved or debossed details go into a surface.
| Min Clearance|
Clearance is the space between any two parts, walls or wires.
To ensure a successful product, make the clearance between parts, walls, and wires greater than the indicated minimum. If your clearance is too small, try making the gap bigger, or consider fusing the parts or features if their independence is unnecessary. You can also try a material with a smaller minimum clearance.
| Min Escape Holes|
Escape holes allow unbuilt material inside hollow products to be removed.
Normally you don't need to consider this, our technician will add escape holes before printing.
When products contain hollow cavities, they are often filled with powder/liquid even after they are removed from the build tray. If escape holes are not large enough, or the geometry of the product makes it difficult to shake or blast the powder out, we cannot successfully clean it.
| Interlocking/moving or enclosed parts?|
Sometimes the interlocking/moving parts can't be printed, since the supports inside the cross section can't be removed.
| Require Support Material?|
Because each layer needs to build off the last, for some material, angles of more than 45 degrees generally require supports to be printed along with the design. Supports are not inherently detrimental for your design, but they do add complexity to the printing process and lead to less smooth finish on overhanging parts.
3D PrinterEOS-P396, EOS-P770, Farsoon-FS403P
Material Spec Sheet
SLS Nylon Glassfilled(PA12+GF) is 3D printed using SLS (Selective Laser Sintering) technology.
Laser sintering is used to build your design with this material.
The models are printed layer by layer by a laser that draws thin lines in the powder, which melts and bonds it together in order to form a thin layer of the model. After a layer is printed, a new layer of fresh powder is spread over the surface by a roller. The printer has a print chamber that is heated to just below the melting point of the powder; the laser beam adds the extra energy to melt the powder, forming a solid model. After a print job is finished, the result is a big block of heated powder with the printed models contained inside.
How is SLS 3D Printing Working?