The go-to material for realistic prototypes, providing excellent details, high accuracy and smooth surface finish with up to 16 micron layer heights.
With Rigid Opaque Plastic, you can 3D print attractive prototypes that closely resemble the ‘look’ of the end product and test fit, form and function, even for moving and assembled parts.
2 x 2 x 2 mm
Default Layer Height:
Optional Layer Heights(mm):
±0.1 mmHeat endurance:
Under 48 ℃
Available Post Process
Suitable ForFunctional prototypes and end products,
Complex designs with intricate details,
Fine-detail models with smooth surfaces,
Moving and assembled parts,
Cases, holders, adapters,
Sales, marketing and exhibition models,
Form and fit testing,
Functional prototyping and testing,
Not Suitable For
Cavities within design (unless making use of escape holes)
Ensure your model can be cleaned
Hard to clean models will be rejected, here's why. During printing, the cavities in your model will be supported by a waxy material which must then be removed before we ship it. While a good deal of this material comes off without any issues, the rest must be scraped away manually with a scalpel. If you design a model with cavities that make such scraping difficult, then unfortunately we cannot produce this model.
A good rule of thumb is that if it can't be cleaned with a scalpel the size of a ball point pen, it will most likely be rejected and require a redesign.
| Min Supported Wall Thickness|
A supported wall is one connected to other walls on two or more sides.
| Min Unsupported Wall Thickness|
An unsupported wall is one connected to other walls on less than two sides.
| Min Supported Wires|
A wire is a feature whose length is greater than five times its width. A supported wire is connected to walls on both sides.
| Min Unsupported Wires|
A wire is a feature whose length is greater than five times its width. An unsupported wire is connected to walls on less than two sides.
| Min Embossed Detail|
A detail is a feature whose length is less than twice its width.
The minimum detail is determined by the printer's resolution.When detail dimensions are below the minimum, the printer may not be able to accurately replicate them. Details that are too small can also be smoothed over in the polishing process.
To ensure details come out clearly, make them larger than the indicated minimum. We may refrain from printing products with details smaller than the minimum, since the final product will not be true to your design. If your product has details smaller than the minimum, try making them larger, removing them, or considering a material with finer detail.
| Min Engraved Detail|
A detail is a feature whose length is less than twice its width. Engraved or debossed details go into a surface.
| Min Clearance|
Clearance is the space between any two parts, walls or wires.
To ensure a successful product, make the clearance between parts, walls, and wires greater than the indicated minimum. If your clearance is too small, try making the gap bigger, or consider fusing the parts or features if their independence is unnecessary. You can also try a material with a smaller minimum clearance.
| Min Escape Holes|
Escape holes allow unbuilt material inside hollow products to be removed.
Normally you don't need to consider this, our technician will add escape holes before printing.
When products contain hollow cavities, they are often filled with powder/liquid even after they are removed from the build tray. If escape holes are not large enough, or the geometry of the product makes it difficult to shake or blast the powder out, we cannot successfully clean it.
| Interlocking/moving or enclosed parts?|
Sometimes the interlocking/moving parts can't be printed, since the supports inside the cross section can't be removed.
| Require Support Material?|
Because each layer needs to build off the last, for some material, angles of more than 45 degrees generally require supports to be printed along with the design. Supports are not inherently detrimental for your design, but they do add complexity to the printing process and lead to less smooth finish on overhanging parts.
3D PrinterStratasys-Connex 350, Stratasys-J750, Stratasys-Objet1000 PLUS
Material Spec Sheet
Polyjet VeroWhite is 3D printed using MJP/Polyjet MultiJet Modeling/Polyjet technology.
PolyJet prototyping technology is used to build your design with this material.
Objet’s patented PolyJet inkjet technology works by jetting photopolymer materials in ultra-thin layers onto a build tray, layer by layer until the model is completed. Each photopolymer layer is cured by UV light immediately after being jetted, producing fully cured models that can be handled and used immediately. The gel-like support material, which is specially designed to support complicated geometries, can easily be removed by hand and water jetting.
How is MJP/Polyjet 3D Printing Working?