SLS Castable Polystyrene (PS)

Back to Materials

SLS Castable Polystyrene (PS)

Polystyrene PSB


This foamed white, amorphous or semi-crystalline thermoplastic has medium hardness and low impact resistance. 3D-printed parts made from PS are used to make master models for vacuum, plaster and ceramic shell castings.


Min. Order Value $66

Est. Lead Time 5 days


Max Build Size

700 x 700 x 500 mm

Min Build Size

50 x 50 x 50 mm

Default Layer Height

0.2 mm

Optional Layer Heights

0.2 mm

Tolerance

±0.3% (with a lower limit of ±0.3 mm)

Heat Endurance

Up to 100 ℃


Smooth ★★★★

Detail ★★

Accuracy ★★★★

Rigidity ★★★

Flexibility

Available Colors

White

Available Post Process

Gallery

Suitable For

Cases, holders, adapters,
Large models,
Functional prototyping and testing,
Jewelry, art

Not Suitable For

Complex designs with intricate details,
Fine-detail models with smooth surfaces

Additional Info

Parts printed with PS are quite fragile, please handle with care, FacFox also provides investment casting service, if you need the final casted parts, you can directly request a casting service to avoid the risk of damage during shipment.

Min Supported Wall Thickness
A supported wall is one connected to other walls on two or more sides.
2 mm
Min Unsupported Wall Thickness
An unsupported wall is one connected to other walls on less than two sides.
2 mm
Min Supported Wires
A wire is a feature whose length is greater than five times its width. A supported wire is connected to walls on both sides.
2 mm
Min Unsupported Wires
A wire is a feature whose length is greater than five times its width. An unsupported wire is connected to walls on less than two sides.
2 mm
Min Hole Diameter
The accuracy of a hole not only depends on the diameter of the hole, but also on the thickness of the wall through which the hole is printed. The thicker the wall section, the less accurate the hole becomes. Through holes must also allow for line-of-sight clearance to ensure all material is cleared during post-processing.
2 mm
Min Embossed Detail
A detail is a feature whose length is less than twice its width.
The minimum detail is determined by the printer’s resolution.When detail dimensions are below the minimum, the printer may not be able to accurately replicate them. Details that are too small can also be smoothed over in the polishing process.
To ensure details come out clearly, make them larger than the indicated minimum. We may refrain from printing products with details smaller than the minimum, since the final product will not be true to your design. If your product has details smaller than the minimum, try making them larger, removing them, or considering a material with finer detail.
1 mm
Min Engraved Detail
A detail is a feature whose length is less than twice its width. Engraved or debossed details go into a surface.
1 mm
Min Clearance
Clearance is the space between any two parts, walls or wires.
To ensure a successful product, make the clearance between parts, walls, and wires greater than the indicated minimum. If your clearance is too small, try making the gap bigger, or consider fusing the parts or features if their independence is unnecessary. You can also try a material with a smaller minimum clearance.
2 mm
Min Escape Holes
Escape holes allow unbuilt material inside hollow products to be removed.
Normally you don’t need to consider this, our technician will add escape holes before printing.
When products contain hollow cavities, they are often filled with powder/liquid even after they are removed from the build tray. If escape holes are not large enough, or the geometry of the product makes it difficult to shake or blast the powder out, we cannot successfully clean it.
10 mm
Interlocking/moving or enclosed parts?
Sometimes the interlocking/moving parts can’t be printed, since the supports inside the cross section can’t be removed.
Require Support Material?
Because each layer needs to build off the last, for some material, angles of more than 45 degrees generally require supports to be printed along with the design. Supports are not inherently detrimental for your design, but they do add complexity to the printing process and lead to less smooth finish on overhanging parts.
No

Feature

Watertight

Foodsafe

Glueable

Recycleable

Biocompatible

Biodegradable

Flame Retardant

Conductive

3D Printer

EOS-P396

Material Spec Sheet

SLS Castable Polystyrene (PS) is 3D printed using SLS (Selective Laser Sintering) technology.

Selective Laser Sintering Process

Laser sintering is used to build your design with this material.

The models are printed layer by layer by a laser that draws thin lines in the powder, which melts and bonds it together in order to form a thin layer of the model. After a layer is printed, a new layer of fresh powder is spread over the surface by a roller. The printer has a print chamber that is heated to just below the melting point of the powder; the laser beam adds the extra energy to melt the powder, forming a solid model. After a print job is finished, the result is a big block of heated powder with the printed models contained inside.

How is SLS 3D Printing Working?