SLA Clear Resin

Back to Materials

SLA Clear Resin

Godart 8001

Clear resin (SLA) has a semi-transparent appearance, but can be post processed to a smooth and almost fully optically clear finish.

Min. Order Value $22

Est. Lead Time 4 days

Max Build Size

600 x 600 x 450 mm

Min Build Size

5 x 5 x 5 mm

Default Layer Height

0.1 mm

Optional Layer Heights

0.1 mm

Tolerance

卤0.3% (with a lower limit of 卤0.3 mm)

Heat Endurance

Up to 50 鈩

Smooth 鈽呪槄鈽呪槄鈽

Detail 鈽呪槄鈽呪槄

Accuracy 鈽呪槄鈽

Rigidity 鈽呪槄鈽

Flexibility 鈽呪槄鈽

Available Colors

Transparent

,

Dyed Clear

Available Post Process

Gallery

Suitable For

Fine-detail models with smooth surfaces,
Cases, holders, adapters,
Sales, marketing and exhibition models,
Low-cost prototype,
Jewelry, art

Not Suitable For

Complex designs with intricate details,
Moving and assembled parts,
Form and fit testing,
Functional prototyping and testing

Additional Info

Min Supported Wall Thickness
A supported wall is one connected to other walls on two or more sides.		 1 mm
Min Unsupported Wall Thickness
An unsupported wall is one connected to other walls on less than two sides.		 1.5 mm
Min Supported Wires
A wire is a feature whose length is greater than five times its width. A supported wire is connected to walls on both sides.		 1 mm
Min Unsupported Wires
A wire is a feature whose length is greater than five times its width. An unsupported wire is connected to walls on less than two sides.		 1.2 mm
Min Hole Diameter
The accuracy of a hole not only depends on the diameter of the hole, but also on the thickness of the wall through which the hole is printed. The thicker the wall section, the less accurate the hole becomes. Through holes must also allow for line-of-sight clearance to ensure all material is cleared during post-processing.		 1.2 mm
Min Embossed Detail
A detail is a feature whose length is less than twice its width.
The minimum detail is determined by the printer’s resolution.When detail dimensions are below the minimum, the printer may not be able to accurately replicate them. Details that are too small can also be smoothed over in the polishing process.
To ensure details come out clearly, make them larger than the indicated minimum. We may refrain from printing products with details smaller than the minimum, since the final product will not be true to your design. If your product has details smaller than the minimum, try making them larger, removing them, or considering a material with finer detail.		 0.6 mm
Min Engraved Detail
A detail is a feature whose length is less than twice its width. Engraved or debossed details go into a surface.		 0.6 mm
Min Clearance
Clearance is the space between any two parts, walls or wires.
To ensure a successful product, make the clearance between parts, walls, and wires greater than the indicated minimum. If your clearance is too small, try making the gap bigger, or consider fusing the parts or features if their independence is unnecessary. You can also try a material with a smaller minimum clearance.		 1 mm
Min Escape Holes
Escape holes allow unbuilt material inside hollow products to be removed.
Normally you don’t need to consider this, our technician will add escape holes before printing.
When products contain hollow cavities, they are often filled with powder/liquid even after they are removed from the build tray. If escape holes are not large enough, or the geometry of the product makes it difficult to shake or blast the powder out, we cannot successfully clean it. 		0 mm
Interlocking/moving or enclosed parts?
Sometimes the interlocking/moving parts can’t be printed, since the supports inside the cross section can’t be removed.
Require Support Material?
Because each layer needs to build off the last, for some material, angles of more than 45 degrees generally require supports to be printed along with the design. Supports are not inherently detrimental for your design, but they do add complexity to the printing process and lead to less smooth finish on overhanging parts.		 Yes

Feature

Watertight

Foodsafe

Glueable

Recycleable

Biocompatible

Biodegradable

Flame Retardant

Conductive
Untested
Untested

3D Printer

Uniontec-RSPro600, ZRapid-SLA660

Material Spec Sheet

SLA Clear Resin is 3D printed using DLP/SLA (Digital Light Processing/Stereolithography) technology.

Stereolithography Process

Stereolithography is used to build your design with this material.Starting from a 3D model, a model is built by cutting it into thin layers via specialized software.

A support structure is created, where needed, in order to deal with overhangs and cavities.

The process takes place in a large tank and begins when a layer of liquid polymer is spread over a platform. This machine then uses a computer controlled laser to draw the first layer onto the surface of a liquid polymer, which hardens where struck by the laser. The model is then lowered and the next layer is then drawn directly on top of the previous one. This is repeated until the model is finished. In this way, layer by layer, an object is 鈥渄rawn鈥 in the liquid by the beam, with the layers being consolidated throughout the process.

When the object is complete, it is raised out of the tank via the supporting platform 鈥 much like a submarine rising to the surface of the water 鈥 with the excess liquid flowing away. The supports are removed manually after the model is taken from the machine.

How is DLP/SLA 3D Printing Working?





銆2025-07-16銆

馃彏锔 Cheers to 10 years! Recharging our creative engines on a team trip to Xinjiang from July 16-24. No delays for production or shipping, just slower replies from customer service!

馃憠More detail
6% OFF for Insta3DP - Automatic 3D printing quotation! Coupon Code: insta3dpbeta2